Jeep Engine Sales -- About Us

How do I order your engine?
Can I custom build my engine?
Can I cancel my order?
How can I identify the VIN code of my engine? What is a Head Casting?
What is a Block Casting?
What is the description of engine long blocks?
What are the engine specifications?
What is your Warranty policy?




Q: How do I order your engine?

A: You can email us your engine order or call us at 1-866-264-5516 with your order of Jeep engine or cylinder head specification.

Back to top

Q: Can I custom build my engine?

A: We can custom build your Jeep engine as needed. When you order your engine ask the salesman about performance options available on that specific engine.

Back to top

Q: Can I cancel my order?

A: You can cancel your order without any charges before we've started building your engine. You will have many opportunities to cancel the order without any charges. Note we confirm the order details before processing it.

Back to top

Q: How can I identify the VIN code of my engine?

A: If your vehicle was manufactured between 1975 to 1980, the VIN/engine code is the 5th digit of your VIN number. If your vehicle was manufactured after 1980, the VIN/engine code is the 8th digit of your VIN number. Note: We will verify this information (if needed) before processing your order.

Back to top

Q: What is a Head Casting?

A: The Head Casting Number is the number that appears on the engine head. Note: We verify this information (if needed) before processing your order.

Back to top

Q: What is a Block Casting?

A: The Block Casting Number is the number that appears on the engine block. Note: We will verify this information (if needed) before processing your order.

Back to top

Q: What is the description of engine long blocks?

A: All long blocks come with cylinder head(s) attached and valve train installed. Valve covers, timing cover, intake manifold and oil pan are not included.

All long blocks have NEW valves, valve springs, valve keepers, push rods, rocker arms, fulcrums, lifters, camshaft, timing chain (belt), timing gears, valve guides (diamond honed), three angle seats, cam, rod and main bearings, pistons, piston rings, rod bushings (if applicable), gaskets and oil pump.

All cylinder blocks, cylinder heads, crankshafts and connecting rods are cleaned and shot peened and magnafluxed for cracks. All bolt holes are tapped.

Cylinder blocks are bored to each piston and diamond honed to 18RMS finish. All oil galleys are hand brushed with white cleaning brushes and cylinders are hand cleaned with cleaning solution and white towels.

Cylinder heads have each valve guide diamond honed, seats are three angle. After assembly, heads are vacuum checked for valve seating.

Crankshafts are ground and polished to 12RMS. Each oil galley is hand brushed with a white cleaning brush.

All connecting rods are honed.

ALL OUR REMANUFACTURED JEEP LONG BLOCKS MEET OR EXCEED THE ORIGINAL GM SPECS


Back to top

Q: What are the engine specifications?

A: Engines remanufactured by our remanufacturing line meet or exceed O.E.M. specifications.

- New Manley valves

- New Elgin valve springs and keepers

- New Badger pistons

- New Hastings molly rings

- New Dynagear timing gears and Durabond cam bearings

- New Dynagear timing gears and chain

- New Elgin lifters, push rods, rockers, balls and nuts

- New Dynagear oil pump

- New FelPro gaskets

- Cylinder heads are pressure checked

- Diamond honed valve guides

- Three angle cut valve seats

- All head surfaces are broached

- Blocks are bored with deck plates, cylinder walls are diamond honed

- Crankshafts are ground and polished for .002 clearance

- Camshafts are ground to O.E.M. specifications, hardened and polished

- Connecting rods are sized to .002 clearance

Back to top

Q: What is your Warranty policy?

A: See below a summary of our engine warranty.

Passenger car and light SUV longblocks are covered for 7 years or 70,000 miles. If failure of a long block should occur during the first twenty-four months and it is determined the failure is due to a defect in workmanship or parts installed by us, we will replace or repair the defective unit to the original buyer. During the balance of the warranty, we will replace the long block at one-half of the current retail price.

The Standard limit labor reimbursement covers labor at $40.00 per hour up to a maximum of $500.00. Premium warranty can be purchased at the time of sale.


Back to top